Lure "bug" made from a wine cork. Making a wobbler from cork with your own hands Assembling bait from soft material

For quite a long time, anglers have had baits such as poppers in their arsenals. This tackle shows excellent results when fishing for pike, so it is widely used among fishermen in our country.

In specialized stores you can purchase a variety of poppers for every color and taste. However, for anglers who like to put their hands to it, I want to offer an example of a popper from a disposable pharmacy syringe.

At minimal cost you can get a homemade, fairly decent catchable popper.

To make a syringe popper you will need the following materials:

syringe five cubes;
wine bottle cork;
two wires;
two tees with winding rings;
steel balls that can be removed from the bearing.

The process of making a homemade syringe popper with your own hands:

Let's get down to the task at hand - making a popper. We disassemble the pharmaceutical syringe and cut off unnecessary parts (we cut the nose, the stem into pieces and use only the middle). The actions can be seen in the photographs.

Cylinders are cut out of a wine cork, which are sized to fit the syringe and will be tightly inserted inside. To do this, use a knife to cut off excess pieces in a circle until the required size is obtained. To avoid mistakes, you can draw the cut location with a ballpoint pen.

Then we push a small cylinder of cork into the syringe to the very end, carefully pierce a hole in it for the wire. Next we send the middle part from the cut rod. We also make holes for the wires in the remaining cylinder, as shown in the photo.

We pour steel balls inside the syringe and push the stopper. We twist the free ends of the two wires and make a ring for attaching the fishing line. We also bend the remaining free ends of the wires and create rings for attaching hooks.

All that remains is to attach the tees with winding rings and a homemade popper - the syringe rattle is ready. You can go to the river and try to catch a predatory pike, which loves to attack such baits.

Homemade syringe popper is ready

All that remains is to add that when making a homemade popper from a syringe with your own hands, you can add something of your own and modify the homemade product, which will certainly lead to an improvement in its quality and catchability. You can add red hairs to the tees, you can also put chopped multi-colored foil inside, or you can come up with your own original equipment for this bait, or an original color.

The hot summer begins to lose its strength. Very soon the temperature will drop a little and the long-awaited autumn will come, when fishermen will take up their spinning rods. A huge number of baits will fly into the expanses of water, with only one purpose - to attract the attention of hunting predatory fish. However, you should not give preference only to store-bought spinners, wobblers and other fishing lures. Without much effort or expense, you can make your own attractive tackle that will work great and bring decent catches. Today I want to talk about how to make a catchy wobbler from a beer cap with your own hands, which is suitable for perch fishing.

To make a homemade simple wobbler you will need:
beer stopper;
paper clips;
2 small self-tapping screws;
triple or double hook with a winding ring;
swivel with clasp;
Styrofoam;
wire cutters.

The process of making a homemade wobbler with your own hands:
1. Take a beer cap and bite off 3 cloves on both sides as shown in the photo. You should have a tail and a front blade.

2. Then with our hands we squeeze the rounded parts of the iron plug towards each other. The result should be a blank for the future wobbler. You can see it in the photo.

3. Cut off a piece of foam plastic with a stationery knife and place it inside a homemade wobbler. This will help increase the buoyancy of the bait and excellent performance when fishing in a pond.
4. We make a hole in the tail blade and use a self-tapping screw to attach a swivel with a clasp and a hook.

5. We make a core from a paper clip that will connect the tail part to the front part and will be attached to the fishing line. The photo shows how to secure this part of the wobbler.

6. It turns out to be an excellent homemade perch wobbler. Now all that remains is to go to the pond, adjust the tilt of the front blade and enjoy catching striped predators.

You can always change the double hook to a triple hook, add or remove the red plastic tail and, as a result of trials and experiments, achieve trouble-free catchability. I wish all anglers a warm autumn and good fishing. Don't be lazy and make your own fishing lures. Good luck!

Classic spinners have been replaced by wobblers that better imitate the behavior of fish. Wobbler production began to gain momentum during a period of bait shortage. Now you can choose a factory model based on price, appearance and properties. But some fishermen prefer to make them themselves, and sometimes homemade wobblers are superior in parameters to their factory counterparts.

Types of wobblers and their characteristics

Before starting the manufacturing process, you need to familiarize yourself with the accepted classification of baits. You can make several wobblers with your own hands for different types of fish and fishing conditions. The design and characteristics are determined in advance.

Types of bait:

According to the nature of their behavior in water - floating, sinking, balanced and surface. Determined by the ratio of the material with and without buoyancy.
According to the form. The crawler is the optimal wobbler for chub. Various rotational movements are provided by a wide blade in the front part of the structure, and releases are located at the rear. However, due to the complexity of the design, their repair is difficult. A homemade wobbler made from a toothbrush is shaped like a popper. It has a small cut off nose and no blades.
Length and weight. Depends on the size, weight and behavior of the fish. The recommended length is no more than 15 cm. Weight affects the choice of spinning rod.

Independent wobbler construction requires special attention to the preparatory stage - the choice of drawing and material of manufacture. As a basis, you can take the factory model and make a number of improvements to its parameters.

Drawings for manufacturing

To make wobblers you need to draw up a diagram. It will include not only a list of materials, but also their characteristics - size, weight, location and method of fastening in the structure. The simplest model consists of a floating body made in the shape of a fish. A wire with detachments is installed in the longitudinal section. She also performs the functions of a sinker. A blade is mounted in the bow.

The advantage of such wobblers is the ability to make repairs in the field. However, they lack an important factor for bait - no sound waves. Therefore, it is better to make a complex wobbler with your own hands on the recommendation of a professional.

It consists of the following parts:

Hollow body divided into three chambers.
Large and small noise chambers located in the frontal part of the bait. To generate sound waves, small plastic balls are placed in them.
Places for attaching hooks.

The disadvantage is that it is problematic to repair such a structure. To make such a beetle wobbler, you will need a complex operation to form cavities in two parts of the workpiece. Recommended material is wood.

Material selection

Most often, wood is used for spinners and wobblers. This material is easy to repair, process and has proper buoyancy. For independent production you will need a minimum of tools that are available in any home workshop. Other materials can be used.

Styrofoam

A foam wobbler is used for fishing at the very surface of the water. This is true for places with abundant vegetation. Polystyrene foam has good buoyancy. The factory model requires a minimum depth of up to 20 cm, which can affect the quality of fishing.

choose foam with the maximum density;
for external processing use fine-grained sandpaper;
When installing cutters and blades, special glue is used;
A small piece of lead is mounted in the middle part for shipping - slight deepening.

The advantages of these baits are that they can be quickly made, repairs are done while fishing. It is enough to pour glue on the damaged part of the structure and wait for final hardening. This is the best pike wobbler for summer fishing.

Tree

The classic bait was originally made of wood, until it was replaced by plastic models. The blank is made from any available piece of wood. For accuracy, you need to use patterns. It is better not to make unhooks for wobblers with your own hands. It is recommended to purchase factory ones to avoid twisting of the fishing line.

Tips for choosing material and manufacturing:

The easiest way to make a wobbler is from cork or other soft wood - cedar or pine.
A complex bait with sound chambers is made from two parts. First, one part is made and a mirror one is made based on its sample.
An engraver is used for fine work.

Particular attention is paid to glue. It should not dissolve in water, while at the same time giving the connection the required reliability. To repair, you will need to disassemble the bait, which often leads to its breakdown. The solution is to make several similar models for quick replacement when fishing.

The video provides detailed instructions for making wobblers with your own hands:

Resin

If you need to repeat the shape of the factory model as accurately as possible, it is recommended to make a wobbler from epoxy. To do this, you will need a mold made of hard plasticine or clay. An imprint of the bait is made on the plate on both sides. These recesses are subsequently filled with epoxy resin.

Before making a wobbler, you will need to perform a number of preparatory steps:

Select a mold material with minimal moisture content. After making the impression, it is advisable to freeze it to preserve the contours.
Filler composition. ECP or EDP are used as a basis. You need 9 parts resin, one part glue and 8 parts fine shavings.
For floating models, after filling one part with resin, a wooden insert is installed.

The final stage is grinding and installation of the gear. It is first tested for buoyancy in a container of water. If required, add a weight. Repairing such a bait is impossible.

Wobblers made from brushes do not have the proper characteristics. Advice from experienced anglers is to spend more time and money to make a truly effective bait.

I present a homemade bait, a wobbler “Beetle” for fish - a chub from the carp family, the bait is made from a wine cork. Detailed process of creating a fishing bait "Chafer beetle" with your own hands. Insects such as grasshopper, chafer beetle and its larva are used as bait for chub. The chub is especially greedy in the spring, in mid-May. The favorite dish of the chub is definitely “Chafer bug” or “Khrushchev”. Homemade wobbler - "Chafer bug" is created as a floating bait on the surface with a slight dive. The bait also works well for perch, which is not averse to profiting from a beetle. For perch, complete compliance of the bait with the original is not very important, and here the active play of this bait, which is ensured by the flexible plastic blade of the wobbler, extending at a large angle to the body of the bait, comes to the fore. Here I sell such baits - https://vk.com/gabodav?w=wall-143764887_10%2Fall
The animation of the bait, which is set by the spinner, is such that concentric circles, characteristic of a real beetle that has fallen into the water, diverge from the beetle across the surface of the water. With such actions you can force a chub or perch to definitely grab the bait. It is important that the bait enters the water in a natural way from the fish's point of view, for example near overhanging tree branches. Ideally after a gust of wind. You need to start the animation with small twitches of the tip of the spinning rod to create diverging circles on the water. The use of such a wobbler is justified during a period when there is a mass emergence of beetles. The appearance of such a delicacy on the water cannot confuse the chub, but on the contrary will force it to catch the tasty treat at any cost. Please note that there should be no fasteners or leashes. This surface bait is a universal wobbler for catching: chub, asp or perch. By the way, ide likes to pamper itself with this delicacy, and you can also catch: large roach, bream, carp, rudd and other non-predatory fish. Recommended fishing time for artificial worm is during the day and evening. Fish bite on the beetle only in warm and clear weather. After heavy rains, the bite noticeably worsens, and sometimes disappears altogether. To make it at home, you need the following: 01. wine stopper; 02. stainless steel wire O 0.8 mm; 03. superglue - Cyanoacrylate; 04. nylon bottle, thickness 0.5 - 0.8 mm; 05. stationery knife; 06. round nose pliers; 07. side cutters; 08. lead for loading; 09. nail polishes; 10. masking tape; 11. a little imagination. --- The composition "The Life and Death of a Certain K. Zabriskie, Patriarch" belongs to the performer Chris Zabriskie. License: Creative Commons Attribution (

Among the variety of plastic wobbler fish, a bait such as a popper has recently become very popular. Invented by American fishermen back in the 30s of the last century, it is now part of the arsenal of any spinning angler. Such popularity of the popper is explained by the structure of its body, features of use, and fishing techniques with it.

Popper is a bladeless surface wobbler with an elongated or slightly rounded body. Its distinctive feature is a funnel-shaped depression in the head part (“spitter”), making it look like a small fish with a wide open mouth. When retrieving, this depression creates characteristic gurgling sounds - as if a fry on the surface is grabbing insects (mosquitoes, midges) that have fallen into the water or are flying low above it.

The length of this bait ranges from 3-4 to 12-15 cm, weight - from 2-3 to 18-20 grams.

The wobbler is equipped with two triple or double hooks with a soft edge. The hooks are located on wire loops-suspensions on the abdomen, in the tail part. The color of the wobbler can be either natural, like a fry of perch, rudd or roach, or bright unnatural colors (acid green, yellow). The wobbler is attached to the fishing line or the latch of the metal leash using a loop with a ring located inside its nose recess.

These fish are made from durable plastic, balsa. Most models have a sound chamber inside the body with small balls, which, when the wobbler plays, create sounds that attract predators.

On a note

When looking for the best popper, most anglers prefer hard plastic models. This material, unlike balsa wood, is stronger, more durable, and less scratched when grabbed by a predator.

Popper classification

A variety of such surface baits is classified depending on the location of the load - the shift of the center of gravity to the tail, head part of the wobbler, or its uniform distribution throughout the body of the bait.

Based on this feature, these wobblers are divided into:

Front-loaded - most of the weight in such baits is concentrated in the head part.
Rear-loaded - the main part of the weight is shifted to the tail of the popper.
Lures with weights distributed evenly throughout the body.

Check the distribution of the load by lowering a popper attached to a fishing line into an aquarium or container with clear water. Based on which part of the wobbler is the most recessed, it is determined which of the types described above it belongs to.

On a note

The division of these plastic fish into floating or sinking poppers is incorrect, since these bladeless wobblers do not dive deeper than 10-15 cm.

Choosing fishing gear

Rod and reel

For fishing with such a wobbler, use a rod with the following characteristics:

Length - 2.1−2.4 meters.
The build is super fast.
Test - 10−30 grams.
The blank material is graphite.

Jig blanks with a thin, sensitive tip are not suitable for fishing with poppers. The spinning rod for this bait is chosen from twitching models, with a hard, durable whip, a comfortable spaced handle made of EVA, and a reliable reel seat.

An inertia-free reel installed on a spinning rod must have the following characteristics:

Forest capacity (size) - 2500−3000.
Gear ratio - 5.0−5.2:1.
The number of bearings is at least 4-5 installed in the transmission mechanism, line roller, knob.
Body material: aluminum alloy, carbon fiber.
Weight - no more than 300 grams.

fishing line

Fishing tackle for popper fishing is equipped with a bright-colored braided cord with a cross-section of 0.08−0.12 mm. Monofilament fishing line with a thickness of 0.18−0.22 mm is used when fishing for perch in small ponds with a maximum casting distance of no more than 15 meters.

On a note

The bright color of the cord is necessary in order to see in low light conditions where the bait is located, to which place it goes at the end of the line.

Fishing technique and tactics

Popper fishing techniques and tactics include the correct choice of place and time of fishing, retrieving, hooking, and retrieving.

Choosing a place and time of fishing

The most successful fishing is with bladeless surface wobblers in the summer, from June to the end of August. In autumn, as it gets colder and aquatic vegetation dies off, their catchability decreases significantly, giving way to heavy sinking wobblers, oscillating spoons, twisters and vibrotails.

Such plastic fish are used in reservoirs where other baits will often cling. Such places include:

Shallow river oxbows and bays overgrown with grass.
Snagged ponds, lakes.
“Zhabovniki” are shallow lakes heavily overgrown with grass, bets.
River sections with weak currents and a large amount of aquatic vegetation on the surface.

Popper fishing is inconvenient and ineffective in clear sections of rivers with medium or fast currents. In such conditions, the wobbler will be strongly carried away by the flow of water and will not animate well.

Wiring Features

When fishing with a popper, use a classic twitching (jerk) retrieve, performed as follows:

After casting, unwind the slack line and wait for a while until the fish stops creating ripples around itself.
In order to easily control the wobbler, the tip of the blank is lowered as close to the water as possible.
After the wobbler has become motionless, they begin to wind the cord with a reel, while making short and sharp jerks with the tip of the rod. Evidence of good wiring is a characteristic gurgling sound and a trail of bubbles left behind the fish.

On a note

The jerk force should be such that the bait does not jump out of the water, but only creates a splash and the necessary sound. Wiring consisting of jerks and pauses lasting 2-3 seconds is also possible. The wiring of the popper depends on the activity of the fish: for a sluggish and inactive predator, wiring with jerks and long pauses is used. When catching active fish, they use a retrieve in which each jerk alternates with a short pause or without it at all.

Hooking and landing

A bite on such a surface wobbler is felt not only “in the hand”, but is also visible visually by the splash next to the wobbler. In this case, they hook with a sharp and short jerk. They land the fish carefully, not giving it the opportunity to drag the wobbler into the bushes, grass, or snags.

How to make a popper yourself

You can make a popper with your own hands from such simple materials as a wine cork or wood.

From the traffic jam

A homemade popper is made from a wine cork using the following technology:

At the ends of the cork, lines are drawn through the center with a marker.
A frame consisting of three hanging loops - front, back and abdominal - is bent from steel wire.
The loops are fixed with a winding of thin copper wire.
The cork is sawed lengthwise to the middle.
A wire frame is placed in the cut.
In the cut, 3-4 notches are also made for loading.
Lead pellets weighing 0.7-1.0 grams are inserted into the recesses.
Fine shavings are poured into the cut and thoroughly impregnated with waterproof transparent glue.
After the glue has dried, the body of the popper is treated with a transparent waterproof varnish.
A hole is made in the beer cork of such a diameter that the front loop of the wire frame passes through it.
The end of the bait and the reverse (flat) side of the beer cap are coated with durable epoxy waterproof glue.
Glue the beer cap to the body of the bait.
Two artificial eyes are glued to the sides of the bait.

You can see the bait making process more clearly in the video below:

Made of wood

The process of making a popper from wood is as follows:

A birch block 5-7 cm long and 1.5-2 cm in diameter is ground to a cone.
The wide (head) part is cut at an angle of about 300.
A recess is made at the end of the wide part - a “spitter”. To do this, first scrape out a small hole with a knife, widen it with a drill and sand it with coarse-grained sandpaper.
A cut is made on the belly of the bait.
A wire frame and loading pellets are inserted into the cut.
Wood shavings mixed with waterproof glue are poured into the cut.
After the glue hardens, the abdomen is treated with sandpaper.

The entire manufacturing process is clearly shown in more detail in the following video:

On a note

More accurate dimensions and drawings for fishing and making such bait can be found on fishing forums.

Hooks

A homemade popper is equipped with strong and large triple, less often double hooks No. 3−2.

Lure coloring

The color does not affect the catchability of the bait in any way - the predator sees it from below and does not react even to the most realistic colors. The color of the wobbler is more important for the angler himself, who needs to see the bait from a long distance in twilight, ripples or waves. Therefore, the best popper should be painted in colors that are visible on the water - green, white, red, etc.

How to choose a popper

Catchable poppers are selected according to length, type of load, based on such criteria as the object being fished and casting distance.

To size

With a bait size of 5-6 cm, the angler can count on catching large perch, small pike, and asp.
For medium and large pike and asp, the most suitable baits are those with a length of more than 7 cm.

By casting distance

If it is necessary to cast over long distances, rear-loaded baits are used.
The best popper for short-range fishing should have a weight located at the front or evenly distributed throughout the body.

On a note

The shape of the popper affects its casting distance. Lures with an elongated body can be cast further than those with a more rounded body.

Popular models

Among the large number of models of poppers for fishing, the most commonly used are the following:

Yo-Zuri EBA Popper 50 mm.
Megabass Pop-X.
Lucky Craft Bevy Popper.
Pontoon 21 Beat Bull.
Kosadaka Takao 70 °F .
Yo-Zuri Hydro Popper R511.

Conclusion

Popper-type wobblers are a universal group of surface plastic fish used by predatory fish species. Their catchability depends both on the correct choice of the bait itself, and the place, time of fishing, and the use of suitable spinning gear.

It might be useful to read: